About: Brad Paugh

Sanden AC Compressor: Inspection Procedures

Leak Checking: 1. Visual Inspection - Although oil seepage does not necessarily indicate leakage of refrigerant, it should be considered a sign that a leak may exist. Look for the following symptoms: a) Oil seepage in shaft seal area (between clutch and compressor) – repairable. b) Pinching or extrusion of front housing O-ring - non-repairable.…

Set of drilled and slotted brake rotors and brake pads for vehicle maintenance.

HOW MUCH DO BRAKES COST?

Brakes are a common maintenance item, and while they aren’t necessarily expensive, it’s certainly an area you don’t want to cut corners with to try and save a few pennies. There are two main types of brakes on passenger vehicles; disc and drum. Drums are usually cheaper to produce and last longer, but disc brakes…

Diagram of fuel pump internals, showing inlet, outlet, and electrical components.

HOW TO REPAIR FUEL PUMP

The fuel pump repair "How To" section of our site is here to help when you need that little bit of extra knowledge to get your project up and running. From the list below select the video or article that is related to info for the product line desired. Common Misdiagnosis Factors for Fuel Fump…

DIFFERENCES BETWEEN USED, REBUILT AND REMANUFACTURED AUTO PARTS

Video Transcription: Knowing the real differences between used, re-built and re-manufactured products go a long way in making an informed decision when it's time to replace the part. The first category is used parts. Some people view these parts as the best value alternative but the danger in choosing these parts is their uncertain…

BuyAutoParts 71-20010 disc brake conversion kit components: rotors, calipers, brackets, cables.

How To Install Disc Brake Conversion Kit (BuyAutoParts Part # 71-20010)

The basic process for a disc brake conversion is very straight forward, but there are always small steps that can be missed. The best way to avoid these small steps is to have a step-by-step installation guide and a mechanic who knows the process. The following article explains how to install a Ford 9" rear…

Power Steering Fluid Recommendations

Steering Tips

Power Steering (PS) fluid provides the necessary hydraulic/fluid pressure for the working of the power steering system. Besides this, it lubricates and cools down the steering components. The PS fluid also acts a sealant and prevents corrosion. The power steering fluid has low compressibility, low volatility, high viscosity and high resistance to fire. With so…

Stainless steel catalytic converter assembly with flanges for exhaust system

Important Information about Catalytic Converters

A catalytic converter reduces the extent of harmful substances in the exhaust gases and releases them as a less-toxic gas into the atmosphere. There are no moving parts in the catalytic converter. The exhaust stream contains raw emissions such as hydrocarbons (HC), carbon monoxide (CO), and nitric oxide (NOX). The catalytic converter reduces the…

Diagram of a knock sensor showing its weight, piezoelectric element, and terminal on an engine block.

HOW TO REPAIR KNOCK SENSOR

For the proper functioning of an automobile, there are various systems that work together and on-board computers which monitor the functioning of various parts. When it comes to the proper functioning of the engine, various mechanisms such as the fuel distribution, fuel injection and ignition timing should be co-ordinated to help it deliver an optimal…

How to Remove a Rusted Wheel Hub Video

The wheel hub keeps the wheels attached to the automobile while letting them move freely on the wheel bearings. It has studs extending out of it, on which the wheel is bolted. Over time, like any part of the vehicle, the wheel hubs tend to wear. The video below shows how to remove a rusted…

Bosch manifold pressure sensor and its location on a car engine

REPAIR MANIFOLD PRESSURE SENSOR

How To Repair Manifold Pressure Sensor The manifold pressure sensor, also known as the manifold absolute pressure (MAP) sensor, senses the air pressure in the engine's intake manifold. These sensors came into use mainly on OBDII engines and are used to calculate the difference between the manifold pressure and the ambient air pressure. With…